Search

Description:This is Yokomo YD-2 Aluminum SLF Big Bore Shock Set Red. Super low friction aluminum big bore shock set for YD-2. The cylinder diameter is wider than the conventional shock, and the shock length is also newly designed for drifting. The maximum capacity for an on-road shock enhances the s..

Description:This is Yokomo YD-2 Aluminum SLF Big Bore Shock Set Purple. Super low friction aluminum big bore shock set for YD-2. The cylinder diameter is wider than the conventional shock, and the shock length is also newly designed for drifting. The maximum capacity for an on-road shock enhances th..

Description:The slide rack set for the YD-2 series has been upgraded to the latest specification. The bulkhead that supports the entire slide rack uses an integrated aluminum type, enabling more accurate machine makeup than ever before. In addition, by changing the bridge at the rear end of the fron..

Description:The slide rack set for the YD-2 series has been upgraded to the latest specification. The bulkhead that supports the entire slide rack uses an integrated aluminum type, enabling more accurate machine makeup than ever before. In addition, by changing the bridge at the rear end of the fron..

Description:This is Overdose Aluminum 6mm One Piece Front Axle Shaft Black For 1/10 RWD Drift. Introducing an aluminum axle shaft with integrated wheel hub exclusively for RWD front. By changing from the conventional steel to aluminum and designing for weight reduction, we have achieved an amazing 1..

Description:A bell crank that can change the mounting position of the tie rod according to the increase or decrease of the front tread. Since the tread can be changed without changing the length of the tie rod as much as possible, the effect on the Ackerman ratio etc. is minimized. In addition, by p..

Description:This is Yokomo YD-2 Series Curved Slide Rack Upper Arm Mount Red. An aluminum mount that supports the rear side of the upper arm used in the roundly slide rack for the YD-2 series...

Description:This is Yokomo YD-2 Series Curved Slide Rack Upper Arm Mount Purple. An aluminum mount that supports the rear side of the upper arm used in the roundly slide rack for the YD-2 series...

Description:This is Overdose GALM Aluminum Turnbuckle Set Red. Aluminum turnbuckle set for GALM. A set of turnbuckles required for GALM. For steering tie rods that require fine adjustment, 0.25, which is half the normal screw pitch, is used. It is possible to adjust the Ackerman and toe angle more d..

Description:This is Overdose GALM Aluminum Turnbuckle Set Purple. Aluminum turnbuckle set for GALM. A set of turnbuckles required for GALM. For steering tie rods that require fine adjustment, 0.25, which is half the normal screw pitch, is used. It is possible to adjust the Ackerman and toe angle mor..

Description:This is Overdose GALM Aluminum Turnbuckle Set Black. Aluminum turnbuckle set for GALM. A set of turnbuckles required for GALM. For steering tie rods that require fine adjustment, 0.25, which is half the normal screw pitch, is used. It is possible to adjust the Ackerman and toe angle more..

Description:Spur gear support plate for evenly mounting your spur gear on your car. Made from Graphite enuring light weight and matching the rotating direction for your motor! Measuring 38mm outer diameter meaning its big enough for all sorts of drift cars!..

Signature Onisiki markings on a spur gear support plate! Perfect for matching with the rest of our electronics and drift parts! Mount your spur evenly with this aluminum Spur Gear Support Plate! The aluminum piece creates an even distributed load which allows for a precise and quiet drivetrain.  ..

Description:This is Overdose Aluminum Adjustable Rear Upright Set Red For XEX GALM Vacula II Yokomo YD-2 YD-4. Introducing adjustable aluminum rear upright. The 2 piece structure of axle mount and the upright base allows various adjustments on toe angles, treads and axle heights. Now available in 3 ..

Description:This is Overdose Aluminum Adjustable Rear Upright Set Purple For XEX GALM Vacula II Yokomo YD-2 YD-4. Introducing adjustable aluminum rear upright. The 2 piece structure of axle mount and the upright base allows various adjustments on toe angles, treads and axle heights. Now available in..

Description:This is Yokomo YD-2 Graphite Battery Holder Set. A graphite battery holder that can be used with the YD-2E / R series and YD-2SXIII. The graphite parts have a solid structure with a plate thickness of 3 mm, and it is possible to hold the battery firmly. Attach a beveled edge design nut t..

Description:This is Yokomo YD-2 Dummy Brake Set Rear Hub Carrier 2 pcs. Rear hub carrier for YD-2 series. Dummy brake calipers can be installed on the rear hub carrier used in the front and rear brake disc / caliper specification sets. By increasing the mounting position of the upper arm and increas..

Description:This is ReveD 2mm POM Spacer 8 pcs Black. This is the standard POM (Duracon) spacer, 4mm inner and 7mm outer diameter. Low friction material has selected and high precision processing has applied for this particular product which is included at RD-008, RD-008B and other HG Front conversi..

Description:This is ReveD 1mm POM Spacer 8 pcs Black. This is the standard POM (Duracon) spacer, 4mm inner and 7mm outer diameter. Low friction material has selected and high precision processing has applied for this particular product which is included at RD-008, RD-008B and other HG Front conversi..

Description:This is ReveD 0.5mm POM Spacer 8 pcs Black. This is the standard POM (Duracon) spacer, 4mm inner and 7mm outer diameter. Low friction material has selected and high precision processing has applied for this particular product which is included at RD-008, RD-008B and other HG Front conver..

..

Description:This is Yokomo High-Precision Cutting Brass M3x6mm Flat Head Screws 10 pcs. It is a brass screw that is used when fixing parts from the bottom of the machine and can be finished with soft rigidity while having the same weight as a steel screw. It is made by high-precision machining, and ..

Description:This is Yokomo High-Precision Cutting Brass M3x10mm Flat Head Screws 10 pcs. It is a brass screw that is used when fixing parts from the bottom of the machine and can be finished with soft rigidity while having the same weight as a steel screw. It is made by high-precision machining, and..

Description:This is Yokomo High-Precision Cutting Brass M3x8mm Flat Head Screws 10 pcs. It is a brass screw that is used when fixing parts from the bottom of the machine and can be finished with soft rigidity while having the same weight as a steel screw. It is made by high-precision machining, and ..

Description: Aluminum curved steering rack for Yokomo's YD-2 series. Providing better a ackermann effect and reduces the effect of bumpsteer which gives a more consistent drift due to the unchanging toe-in/out!..

Description:This is Wrap Up Next Brass 53.6-56.8mm YD Suspension Mount CDD Golden Black For YD-2 Series NERVIS-R KCR...

Description:This is Wrap Up Next Brass 50-53.2mm YD Suspension Mount CCD Golden Black For YD-2 Series / NERVIS-R / KCR...

Description:This is Wrap Up Next Brass 46.4-49.6mm YD Suspension Mount C Golden Black For YD-2 Series / NERVIS-R / KCR...

Description:This is Wrap Up Next Brass 43.5-46.7mm YD Suspension Mount B Golden Black For YD-2 Series / NERVIS-R / KCR...

Description:This is ReveD Alumimum Front Upper Arm Mount Bell Crank Black...

Description:Mount your spur evenly with this aluminum Spur Gear Support Plate! The aluminum piece creates an even distributed load which allows for a precise and quiet drivetrain. Comes in the signature black with red highlighted edges and laser engraved Xpress logo!..

Description:This is Wrap Up Next Overhead Concept Motor Conversion Kit Black For Yokomo YD-2...

Description:This is Overdose Stock Shock Set Black For 1/10 RC Drift .A set of 4 shocks that comes standard with the OD chassis kit. It is a luxurious specification with a piston machined from fluororesin and a shock shaft guide with a hard alumite + fluorine coated cylinder. Set of 4 Spring is not ..

Description:This is Overdose Setup Bladder Set For HG Shock. ..

Description:This is a pack of nylon front axles spacers for Team Associated trucks and buggies. You can also use these to adjust the camber link locations under the ball studs...

Description:Introducing a new design with an OD wire clamp that tightens the chassis with a cool design. The conventional square design has been redesigned into a sharp and three-dimensional design. In addition, the front and rear length is designed to be short so that it is easy to install even..

Description:Introducing a new design with an OD wire clamp that tightens the chassis with a cool design. The conventional square design has been redesigned into a sharp and three-dimensional design. In addition, the front and rear length is designed to be short so that it is easy to install even..

Description: Introducing a new design with an OD wire clamp that tightens the chassis with a cool design. The conventional square design has been redesigned into a sharp and three-dimensional design. In addition, the front and rear length is designed to be short so that it is easy to install e..

Description: This is a Yokomo YD-2S Series Titanium High Precision Cutting 4.8mm Ball End Set. It is a set for changing the rod end ball of the upper arm and tie rod of the RWD drift car YD-2S series to Φ4.8mm. Uses high-precision cutting titanium balls for a lightweight finis..

Description:This is Yokomo YD-2 Plastic Mold Main Chassis...

Description:A front shock tower that fits into all YD-2 series cars. The upper shock tower ensures sufficient rigidity by being lightweight and highly rigid graphite with 3 mm thick. The upper arm holder is made of aluminum to increase rigidity and accuracy. The lineup includes three colors of b..

Description:A front shock tower that fits into all YD-2 series cars. The upper shock tower ensures sufficient rigidity by being lightweight and highly rigid graphite with 3 mm thick. The upper arm holder is made of aluminum to increase rigidity and accuracy. The lineup includes three colors of b..

Description:A front shock tower that fits into all YD-2 series cars. The upper shock tower ensures sufficient rigidity by being lightweight and highly rigid graphite with 3 mm thick. The upper arm holder is made of aluminum to increase rigidity and accuracy. The lineup includes three colors of b..

Description: This is ReveD R-tune 2WS Front Spring Soft 2 pcs Black For 1/10 RC Drift. Introducing the R-tune series for the 2WS (two-way short) style front spring. The design has been very popular due to its overwhelming control performance! Compared to the current RD-006F 2WS front spring, w..

Description: This is ReveD R-tune 2WS Front Spring Hard 2 pcs Black For 1/10 RC Drift. Introducing the R-tune series for the 2WS (two-way short) style front spring. The design has been very popular due to its overwhelming control performance! Compared to the current RD-006F 2WS front spring, w..

Description: This is ReveD HG Bell Crunk Spec Front Conversion Kit Black For Yokomo YD-2. The newly developed upper arm mount for bell cranks can be mounted on both aluminum bulkheads and plastic bulkheads.The aluminum upper arms are a lightweight design and shape which has 2pcs ball bearings ..

Description:This is ReveD Aluminum 6mm Spring Retainer 2 pcs Black For 1/10 RC Drift. Team RêveD has been testing and developing this new product on various road surfaces with awesome results! We have a new spring seat that suppresses spring vibration and demonstrates suspension performance more..

Description:This is Overdose HG Shock Spec.3 28mm Shock Shaft Set. This shock shaft is used as standard in Spec.3. By changing the shaft length from the conventional 27mm to 28mm, it is possible to extend the shock stroke...

Description:This is Overdose HG Shock Spec.3 1.85T Machined PTFE SC Shock Piston Set. ..

Description:This is Overdose HG Shock Spec.3 1.50T Machined PTFE SC Shock Piston Set...

Description:This is Overdose HG Aluminum Full Adjustable Shock Set Spec.3. The popular high-grade shock has evolved to spec.3 with smooth movement due to the friction loss suppressed to the limit. The piston thickness is thinner than the pistons up to spec.2, and the rise of damping at the begin..

Description: This is ReveD MC-1 Slide Rack Spec. Conversion Kit. RêveD main designer Hayato Matsuzaki along with the Rêve D development team and team drivers all worked together to bring the prototype car into reality. It has taken roughly a year for us to complete the optimum specifications f..

Description: This is ReveD MC-1 Bell Crank Spec. Conversion Kit. RêveD main designer Hayato Matsuzaki along with the Rêve D development team and team drivers all worked together to bring the prototype car into reality. It has taken roughly a year for us to complete the optimum specifications f..

Description:This is Yokomo YD-2S Sliderack Matte Graphite Upper Deck Set Black...

Description:This is Yokomo YD-2 Series Rear ESC Mount Set Purple. A ESC mount set that can change the weight balance of the chassis by mounting the ESC on the rear overhang and greatly enhance the rear traction. Especially effective on roads with low grip, the load applied to the rear tires at t..

Description:This is Yokomo YD-2 Series Brass 60.8mm-64mm Suspension Mount E Black Golden. A brass suspension mount that is ideal for the rear suspension of the YD-2 series. We have a lineup of D and E sizes, which are the same as the standard kits such as SXIII, and increase rear traction by mak..

Description:This is Yokomo YD-2 Series Brass 57.2mm-60.4mm Suspension Mount D Black Golden. A brass suspension mount that is ideal for the rear suspension of the YD-2 series. We have a lineup of D and E sizes, which are the same as the standard kits such as SXIII, and increase rear traction by m..

Description:This is Yokomo Slide Rack Bulkhead Set Ver.2 For YD-2E YD-2S Series. The slide rack set for the YD-2 series has been upgraded to the latest specification. The bulkhead that supports the entire slide rack uses an integrated aluminum type, enabling more accurate machine makeup than ever be..

Description:This is Axon Revoshock II Damper Kit For Yokomo YD-2 YD-4. The outer diameter of the piston, which greatly affects the maximization of damper capacity, which is important for producing high traction, is 11.5 mm, which is the size of a high big bore. And the clearance between the pist..

Description:This is Axon Low Friction Soft Type REV O-Ring II Set For Yokomo YD-2 / YD-4...